適用于公路、建筑、地質冶金，保溫材料，科研等部門的試驗室對物料進行篩分分析，既方便又簡單完成分級工作。
    用途：分樣篩振擺儀主要由擺動機構，震擊機構，夾緊機構等部分組成。電動機通過轉動軸，蝸輪付帶擺動架上的主偏心軸旋轉，從而又連帶動其它兩個付偏心軸回轉促使整個篩組的擺動半徑，也等于偏心距的平面圓周擺動。同時在同一臺電動機帶動另一對蝸輪付通過凸輪，頂桿裝有篩組的擺動架，周期地頂起靠自重下落在機座的砧座上，使擺動架得到平面圓周擺動的同時進行震擊。
      測厚儀多功能振篩機測厚儀多功能振篩機 礦物棉渣球篩分振篩機參數：
    1．篩子直徑： 200mm-
    2，震幅； 10mm
    3．振擊次數： 23.5次／S
   4，輸入電源：三項220V
      礦物棉 渣球篩分振篩機1、在按放篩子時，應按照篩孔大小順序迭放，同時另加一個篩子底盤。
    2、將需篩分化驗的物料倒入最上層的篩子內，蓋好篩蓋然后按放在振擺儀承篩座內。
    3、反時轉夾篩盤上的膠木手柄，將整個夾篩盤向下滑在套篩上，然后，再順時針旋轉夾篩盤上膠木柄，其內的頂桿軸夾緊承座，把整套分樣篩固緊。
    4、把振篩機上的定時器旋鈕撥到篩析所需時間，打開電源開關，振擺就會開始篩轉式的工作。
    5、待定時器到達先定時間的定位，振擺儀自動停止工作。
    6、反時針旋轉夾篩盤上的膠木手柄將央篩盤松開并向上提，固定在滑套上，取下分樣篩。依次將需析后殘留在各號篩子內的物粒用天平稱重精確到檢析比例